PlaceDossier / Questions

Who can install or replace a well pump in BC, and can I do it myself?

A registered well pump installer or driller, or someone they directly supervise, must install, repair or pull a well pump; an owner may only do smaller jobs, such as disinfecting their own well and pump.

Opens the lot's report at this answer. If an address isn't found, try the PID, the 9-digit parcel number on the land title or assessment notice.

Share

TextEmail

Text and Email open your messages or email app with this message, ready to edit.

What the answer means

Most wells on rural lots have a pump in them, and a pump wears out long before the well does. BC treats work on a well pump as regulated well work: the Water Sustainability Act says who may do it, and its Groundwater Protection Regulation says how the well must be left. The rules below are the same across BC.

Who may do it
A person who installs, maintains, repairs, removes or tests a well pump or a wellhead, runs a flow test, or disinfects a well pump must be a well pump installer or well driller qualified for it, or work under the direct supervision of one or of a professional in hydrogeology or geotechnical engineering (Water Sustainability Act s. 50 (1), (2)). A well pump is a pump at or in a well used to take groundwater from it, recharge it or dewater an aquifer (s. 1). A registered well pump installer holds SkilledTradesBC's Well Pump Installer certificate or an equivalent (Groundwater Protection Regulation s. 10 (2)); a registered water well driller is qualified for pump work on water supply wells too (s. 14 (2)). Both are on the Province's registers and carry its identification card, which they must show when asked (Act s. 51 (3); Regulation s. 13).
What an owner may do
The Act lets an owner, without a qualified person, disinfect a well pump they own (s. 50 (4) (b)), deactivate or disinfect a well they own (s. 49 (3) (b)), and install, replace or repair a flow meter, or a well cap, well cover, valve or vent at the wellhead reachable at the ground's surface, on their own well (s. 49 (3) (d)). But s. 50 (1) also reserves installing, maintaining, repairing or removing a wellhead, which the cap sits on, to the same trades and names no owner exception for it, so whether an owner may change a cap themselves is unclear (our reading). It makes no exception for an owner installing, repairing or pulling the pump in their own water supply well, and the regulation names none we found, so that's the trades' work (our reading). A pump in a monitoring, geotechnical or closed-loop geoexchange well is left out of the rule (s. 50 (4) (a)). Whether a pump in the house drawing from the well counts as "at" the well is unclear: the Act doesn't say how near.
How the pump goes in
Whoever installs it must keep the casing from being damaged or moved, put a liner in an unstable well, keep foreign matter out and leave the well, pump and parts able to be disinfected (Regulation s. 44). A pitless adapter's joint with the casing must be watertight (s. 45); a liner, drop pipe or sounding tube in a water supply well must be approved or certified for drinking water (s. 46); a permanent pump needs a device stopping water flowing back into the well (s. 47); and only non-toxic lubricants and solvents may be used (s. 50).
The seal and the cap
If the pump work damages the surface seal, the installer must repair or replace it to the regulation's standard; in a well with no seal, an open gap the work leaves round the casing must be filled with sealant (s. 48). If the wellhead is changed, it must still meet the regulation after (s. 49). The owner must keep a well cap that meets the regulation secure on the casing and in good condition, and fit one where there's none (s. 39 (1), (2)); where the owner can't, a qualified installer, driller or professional designs and fits one (s. 42 (1)).
Disinfecting after
Whoever installs a permanent pump, one meant to stay more than 90 days (s. 1), or removes a temporary one must disinfect the groundwater in the well to kill anything the work brought in (s. 52). How that's done, and the water test after, are on treating well water and testing a well.
The record
The person responsible for installing a well pump must keep a daily log and complete a report "subject to the regulations", give the owner a copy, and produce both when an official asks (Act s. 57 (1) (b), (2), (3) (a)). The regulation's report sections set out only well construction, decommission and identification reports (ss. 76 to 80), and pump work isn't an alteration of the well (Act s. 1), so what pump report an owner gets is unclear: ask the installer for a written record. The owner must keep the well's construction report and every flow test report until the well is decommissioned, and pass them to the buyer on a sale (Regulation s. 81 (2), (4)).
The wiring
Electrical work needs a permit for each structure with its own supply (Electrical Safety Regulation s. 11). A homeowner may do it in the detached house they live in under a homeowner permit, single phase at no more than 200 amps and 150 volts to ground, with inspections (s. 17); a well pump isn't on the list of things an individual may swap like for like without a permit (s. 18 (2)), so ask Technical Safety BC, or the city that issues its own permits, before rewiring one (our reading).
What it means for a buyer
A pump replaced by someone off the registers, or a wellhead left open, is a cost and a water quality question that passes with the house. The owner, not the installer, keeps the wellhead sloped, clear and in good repair (Regulation s. 58), so after you buy that's yours.

Our summary of the Water Sustainability Act (SBC 2014, c. 15, ss. 1, 48 to 51, 57), the Groundwater Protection Regulation (B.C. Reg. 39/2016, ss. 1, 10, 13, 14, 39, 42 to 52, 58, 81) and the Electrical Safety Regulation (B.C. Reg. 100/2004, ss. 11, 17, 18) on BC Laws, read 2026-10-28. The Groundwater Protection Regulation's consolidation there was current to November 29, 2022; later amendments, if any, aren't in it. This isn't legal advice.

Sources (read 2026-10-28; summarised in our own words unless noted): Water Sustainability Act, SBC 2014, c. 15 (ss. 1, 48 to 51, 57); Groundwater Protection Regulation, B.C. Reg. 39/2016; Electrical Safety Regulation, B.C. Reg. 100/2004 (ss. 11, 17, 18); Registers of well drillers and well pump installers, Province of BC (read 2026-10-28); Groundwater wells and aquifers (GWELLS), Province of BC (read 2026-10-28).

Before you buy: who to ask

The seller or their agent
When was the pump last installed, repaired or pulled, by whom, and is there a record of it? Do you have the well construction report and any flow test?
A registered well pump installer or well driller
Is the cap secure, the seal whole and the ground sloped away from the wellhead, and what shape is the pump in?
Technical Safety BC, or the city
Was the pump's wiring done under a permit, and is that permit closed?

Look up the lot above: its report gives the wells on record within 2 km with their median depth, yield and water level, and the aquifer under the lot.

See also water wells, drilling a new well, testing a well, treating well water, electrical permits and backup generators.

Buying rural land? Before you buy rural land in BC: the nine questions that decide an offer, on one printable page.