Does a BC chimney or wood stove need an inspection, and what is a WETT inspection?
The BC Fire Code has every chimney inspected at least once a year and after a chimney fire; a new wood stove goes in to CSA B365, with a permit where the council's bylaw asks.
Opens the lot's report at this answer. If an address isn't found, try the PID, the 9-digit parcel number on the land title or assessment notice.
What the answer means
Two codes cover a chimney and a wood stove. The BC Fire Code applies to every house, old or new: its chimneys, flues and flue pipes are inspected at least once a year, cleaned before deposits build up, and repaired when they decay. The BC Building Code applies when a stove or chimney goes in: the stove is installed to CSA B365, and the council's building bylaw says whether that needs a permit and who inspects it.
- Every chimney, every year
- Every chimney, flue and flue pipe is to be inspected for any dangerous condition at intervals of no more than 12 months, whenever an appliance is added, and after any chimney fire (BC Fire Code, Division B, Sentence 2.6.1.4 (1)). The Fire Code applies to all new and existing buildings (Division A 1.1.1.1 as the Province amends it), so a house built long ago is held to this inspection too (our reading), though equipment put in under an earlier edition of the code may stay as installed (Division A 1.1.1.1 (2)).
- Cleaning and repair
- Chimneys, flues and flue pipes are cleaned as often as needed to keep them free of dangerous build-ups of combustible deposits, and repaired or replaced to fix any structural deficiency or decay, with unused openings sealed against fire and smoke (2.6.1.4 (2), (3)). Heating appliances, chimneys and flue pipes are run and kept so they don't create a hazard (2.6.1.6 (1)).
- Clearances
- The clearances the Building Code sets between a chimney, flue pipe or stove and anything combustible are to be kept, and nothing combustible may sit in that space or by an ash pit or cleanout door (Fire Code 2.6.1.5): firewood stacked against the stove, for one (our reading).
- Putting in a stove
- The BC Building Code 2024 has a solid-fuel appliance designed, built and installed, combustion air included, to CSA B365, the installation code for solid-fuel-burning appliances (Division B, Sentence 9.33.5.3 (1)). A fireplace insert or a stove vented through a fireplace's throat meets ULC-S628 and is installed to CSA B365 (9.22.10), and a factory-built chimney serving a wood stove meets CAN/ULC-S629, the 650 °C chimney standard (9.33.10.2 (1)).
- Masonry chimneys
- A chimney's walls are smoke- and flame-tight (9.21.1.2). A flue serving a fireplace serves no other appliance, and one serving a wood stove isn't connected to a natural gas or propane appliance (9.21.2.1 (1), (2)). The flue rises at least 900 mm above the highest point where the chimney meets the roof and 600 mm above any roof or structure within 3 m of it (9.21.4.4 (1)).
- A permit
- Whether a new stove, insert or chimney needs a permit, and who inspects it, is the council's or regional district's building bylaw, and the two we read differ. The District of Saanich takes a chimney, fireplace and woodstove permit application for new and replacement installs, holds them to the present BC Building Code, and accepts no woodstove or insert made before 1993. The City of Nanaimo doesn't inspect woodstove installs itself; where one goes into a new home or a renovation under a building permit, it asks for the stove to be inspected by a WETT-certified inspector, and it points anyone installing their own to CSA B365. Where no one issues building permits on rural land, see building permits.
- What a WETT inspection is
- WETT (Wood Energy Technology Transfer) is a private training and certification program for people who install, sweep and inspect wood-burning systems, the certification Nanaimo names. No BC law we read licenses chimney inspectors or sweeps, so a WETT report is a certified person's check against the maker's instructions and the codes, not a government inspection (our reading).
- Which stoves, and what may burn
- Which stoves may be sold and what may be burned in them is the Province's Solid Fuel Burning Domestic Appliance Regulation, and in Metro Vancouver its own bylaw (see wood stoves); Saanich's application asks for a solid fuel declaration.
- Carbon monoxide alarms
- New work that adds a fuel-burning appliance brings the Building Code's carbon monoxide alarms near the bedrooms (Division B 9.32.4.2), as Saanich's application notes (see smoke and CO alarms).
- What it means for a buyer
- Ask when the chimney was last inspected and swept, whether there has been a chimney fire since, whether the stove was installed under a permit, and the stove's make, model and year from its label. An insurer may ask for an inspection before it covers a house heated with wood: ask it what it needs before subjects come off (see home insurance).
Our summary of the BC Fire Code (Division A 1.1.1.1 as amended by the British Columbia Fire Code Order, Ministerial Order FSA 2023 1; Division B 2.6.1.4 to 2.6.1.6, which the Order leaves unamended, read in the 2018 BC Fire Code's same articles), the BC Building Code 2024 (Division B 9.21.1.2, 9.21.2.1, 9.21.4.4, 9.22.10, 9.32.4.2, 9.33.5.3, 9.33.10.2), the District of Saanich's chimney, fireplace and woodstove permit application (June 2024) and the City of Nanaimo's woodstove installations page, read 2026-10-23. Each local government's building bylaw sets its own permit rules: ask yours.
Sources (read 2026-10-23; summarised in our own words unless noted): British Columbia Fire Code Order, Ministerial Order No. FSA 2023 1, and its Schedule; British Columbia Fire Code 2018, Division B, Section 2.6 (Articles 2.6.1.4 to 2.6.1.6); British Columbia Building Code 2024 (Division B, 9.21, 9.22.10, 9.32.4.2, 9.33.5.3, 9.33.10.2), Province of BC; Application for Chimney/Fireplace/Woodstove Permit (June 2024), District of Saanich; Woodstove Installations, City of Nanaimo.
Before you buy: who to ask
- The seller or their agent
- When was the chimney last inspected and swept, and by whom? Has there been a chimney fire? When was the stove put in, and under what permit?
- The local government
- Is there a permit and final inspection on file for the stove, insert or chimney, and what does putting one in need here?
- Your home inspector or a specialist
- Does the stove carry a certification label, are the clearances and the floor protection right, and should a certified chimney inspector look inside the flue?
- Your insurer
- Will you cover the house heated with this stove, and what inspection or paperwork do you need first?
How cold the place gets, and how many days a winter its air is poor, is in the report's climate section: look up the lot above.
See also wood stoves, home insurance, home inspections, smoke and CO alarms, firewood and building permits.