PlaceDossier / BC places / Aquifers

Aquifer 86: Pineview

Aquifer 86 (Pineview) is a confined sand and gravel (glacial) aquifer of 143 km² in the Fraser-Fort George Regional District, mapped in 2012. The province rates its productivity high, its vulnerability to contamination from the surface low, and the demand on it low. 206 wells on record are linked to it; water-supply wells there are typically 110 m deep and tested at a median 68.1 L/min. It lies under Fraser-Fort George, Electoral Area D (78%), Prince George (22%).

BC aquifer 86 · sand and gravel · 143 km² · Fraser-Fort George

How the province rates it

Productivity high, vulnerability low, demand low.

RatingWhat it means
Productivity
how much water the aquifer gives up to wells, judged from well yields, the aquifer material and pumping tests
highWells here tend to yield well. The Province's aquifer classification guide puts high productivity at coarse sand and gravel, or typical well yields over about 3 L/s (180 L/min).
Vulnerability
how easily something spilled at the ground surface could reach the water, judged from what lies above the aquifer and how deep the water is
low (class C)Better protected (class C), usually by clay or silt above it or deep water. Not immune: a gap in the cover or a badly sealed well can still let contaminants in.
Demand
how much the aquifer is used now, judged from the number and density of wells and what they're used for
lowLightly used: about 4 or fewer domestic wells per km² where homes rely on private wells.
Level of development Inferred
demand compared with productivity
Light (class III)Read by us from the guide's table of demand against productivity; where it gives two classes the mapper chose with local knowledge. Heavy (I): new wells should be carefully assessed; moderate (II): given careful thought; light (III): more use is usually fine if the aquifer can supply it.

Ratings are the province's, set when the aquifer was mapped (2012) from wells, geology and local studies. Vulnerability is about the ground, not what's built on it: a well-protected aquifer under a busy area can still be at more risk than an exposed one in the bush.

Sources: Ground Water Aquifers, Water Protection and Sustainability Branch, Province of BC and Groundwater Wells (GWELLS), Province of BC, as published on October 1, 2026 (Open Government Licence – British Columbia); ratings explained after Berardinucci and Ronneseth (2002), Guide to Using the BC Aquifer Classification Maps for the Protection and Management of Groundwater, BC Ministry of Water, Land and Air Protection. Summaries by PlaceDossier.

The wells in it

206 wells on record are linked to this aquifer.

Wells linked206 (121 water-supply)
Water-supply well depthmedian 110 m; middle half 50.1 m to 136 m (120 wells)
Tested yieldmedian 68.1 L/min; middle half 37.9 L/min to 131 L/min (98 wells tested)
Water level below groundmedian 86.6 m when drilled (97 wells)
Drilled1942 to 2015
Well depth deeper than 96% of the 637 BC aquifers with at least 10 wells with a depth
131030100300 m Median 110 m from 120 wells
Tested yield higher than 70% of the 542 BC aquifers with at least 10 wells tested
1310301003001,0003,000 L/min Median 68.1 L/min from 98 wells

This aquifer's medianIts middle half of wellsAnother BC aquifer's median

Depths are how deep the driller finished the well; yields are the driller's test, often an hour or less, in litres per minute. A domestic well's yield is usually judged against the household's peak use; ask a driller what's enough for yours.

What the water tested for

The median was over Health Canada's limit at some of the wells sampled here: arsenic at 1 of 6, manganese at 5 of 6.

6 wells in this aquifer were sampled for the Province's records from 2007.

Typical well (median)Highest sampleSamples over the limitWells
Arsenic
limit 0.010 mg/L
0.00095 mg/L0.0141 mg/L1 of 6 samples, at 1 well6
Manganese
limit 0.12 mg/L; 0.02 mg/L for taste and staining
0.37 mg/L1.34 mg/L5 of 6 samples, at 5 wells
6 over the taste and staining level
6
Uranium
limit 0.02 mg/L
0.0057 mg/L0.0158 mg/Lnone of 6 samples6
Lead
limit 0.005 mg/L
0.00058 mg/L0.00382 mg/Lnone of 6 samples6

These are samples of raw water, before any treatment, from wells in the Province's environmental monitoring records since 2000: its observation wells and groundwater surveys, water systems' wells and other drinking-water wells; wells at landfills, mines and permit holders' works are left out. A result below the lab's detection limit counts at that limit. Lead mostly comes from a well's pipes and fittings rather than the aquifer. Groundwater changes over short distances and with depth, so a nearby well says what the aquifer can hold, not what a well on this lot gives. Bacteria aren't shown: they depend on how each well is built and kept. Health Canada's Guidelines for Canadian Drinking Water Quality set the most a drinking water should hold: arsenic 0.010 mg/L, fluoride 1.5 mg/L, manganese 0.12 mg/L (and 0.02 mg/L for taste and for staining laundry and fixtures), uranium 0.02 mg/L, nitrate 10 mg/L as nitrogen (45 mg/L as nitrate) and lead 0.005 mg/L, with arsenic and lead kept as low as reasonably achievable. Our summary of Health Canada's summary table, read 2026-10-11.

Test your own well, for bacteria and these, at an accredited lab; your health authority can say which labs take samples from private wells. Health authority contacts.

Source: Environmental Monitoring Data System (EnMoDS) results, Province of BC (Open Government Licence – British Columbia); Health Canada's guidelines. Wells are those the Province links to this aquifer; a well with no link counts here when this is the only mapped aquifer under it. Wording by PlaceDossier.

Where it is

N 05 km

The aquifer's outline as the Province maps it. Zoom in to see the lots over it; tap one for its report.
Share

TextEmail

Text and Email open your messages or email app with this message, ready to edit.

KindConfined sand and gravel - glacial
Geological unitTertiary channel sand and gravel deposits
Location, as describedPineview to Buckhorn
Area143 km²
Water useSeveral uses (for example household wells, water systems, irrigation or industry)
Water quality concernsNone documented
Mapped2012

Confined: a layer of clay, silt or till lies over it, which slows water (and spills) from the surface; wells reach it through that layer. The province's page for this aquifer lists the studies behind it and its observation wells: GWELLS aquifer 86.

Sources: Ground Water Aquifers, Water Protection and Sustainability Branch, Province of BC and Groundwater Wells (GWELLS), Province of BC, as published on October 1, 2026 (Open Government Licence – British Columbia); ratings explained after Berardinucci and Ronneseth (2002), Guide to Using the BC Aquifer Classification Maps for the Protection and Management of Groundwater, BC Ministry of Water, Land and Air Protection. Summaries by PlaceDossier.

What this record doesn't cover

The province maps aquifers where wells and studies give enough to go on, mostly in settled valleys; most of BC isn't mapped, and a lot outside every outline can still have groundwater. Outlines are drawn from geology and well logs at the scale of the study, so an edge can be well off on the ground, and one aquifer can lie under another. Wells are linked to an aquifer by provincial staff from the driller's log: not every well inside an outline is linked, and well depths and yields are as the driller reported them, often from a short test.

These are mapped ratings and drillers' records, not a test of any one lot. Before you buy a property on a well, or plan to drill, ask a qualified hydrogeologist or a registered well driller what this aquifer gives where you are, and test the water.