PlaceDossier / BC places / Aquifers
Aquifer 800: South Valemount
Aquifer 800 (South Valemount) is a confined sand and gravel (glacial) aquifer of 18 km² in the Fraser-Fort George Regional District, mapped in 2006. The province rates its productivity low, its vulnerability to contamination from the surface moderate, and the demand on it low. 12 wells on record are linked to it; water-supply wells there are typically 31.9 m deep and tested at a median 17 L/min. It lies under Fraser-Fort George, Electoral Area H (89%), Valemount (11%).
BC aquifer 800 · sand and gravel · 18 km² · Fraser-Fort George
How the province rates it
Productivity low, vulnerability moderate, demand low.
| Rating | What it means | |
|---|---|---|
| Productivity how much water the aquifer gives up to wells, judged from well yields, the aquifer material and pumping tests | low | Water comes slowly. The low band in the Province's aquifer classification guide is silt, fine sand or fractured bedrock, or typical well yields under about 0.3 L/s (18 L/min). A well may still supply a house, but it isn't assured. |
| Vulnerability how easily something spilled at the ground surface could reach the water, judged from what lies above the aquifer and how deep the water is | moderate (class B) | Some natural protection (class B), which can vary across the aquifer. |
| Demand how much the aquifer is used now, judged from the number and density of wells and what they're used for | low | Lightly used: about 4 or fewer domestic wells per km² where homes rely on private wells. |
| Level of development Inferred demand compared with productivity | Moderate (class II) | Read by us from the guide's table of demand against productivity; where it gives two classes the mapper chose with local knowledge. Heavy (I): new wells should be carefully assessed; moderate (II): given careful thought; light (III): more use is usually fine if the aquifer can supply it. |
Ratings are the province's, set when the aquifer was mapped (2006) from wells, geology and local studies. Vulnerability is about the ground, not what's built on it: a well-protected aquifer under a busy area can still be at more risk than an exposed one in the bush.
Sources: Ground Water Aquifers, Water Protection and Sustainability Branch, Province of BC and Groundwater Wells (GWELLS), Province of BC, as published on October 1, 2026 (Open Government Licence – British Columbia); ratings explained after Berardinucci and Ronneseth (2002), Guide to Using the BC Aquifer Classification Maps for the Protection and Management of Groundwater, BC Ministry of Water, Land and Air Protection. Summaries by PlaceDossier.
The wells in it
12 wells on record are linked to this aquifer.
| Wells linked | 12 (10 water-supply) |
|---|---|
| Water-supply well depth | median 31.9 m; middle half 27.5 m to 42.2 m (10 wells) |
| Tested yield | median 17 L/min; middle half 8 L/min to 26.5 L/min (10 wells tested) |
| Water level below ground | median 19.5 m when drilled (10 wells) |
| Drilled | 1978 to 2021 |
This aquifer's medianIts middle half of wellsAnother BC aquifer's median
Depths are how deep the driller finished the well; yields are the driller's test, often an hour or less, in litres per minute. A domestic well's yield is usually judged against the household's peak use; ask a driller what's enough for yours.
What the water tested for
The median manganese was over Health Canada's limit at 1 of 1 wells sampled here.
1 well in this aquifer was sampled for the Province's records from 2021, one of them the Province's observation well 502.
| Typical well (median) | Highest sample | Samples over the limit | Wells | |
|---|---|---|---|---|
| Arsenic limit 0.010 mg/L | 0.0001 mg/L | 0.0001 mg/L | none of 1 sample | 1 |
| Fluoride limit 1.5 mg/L | 0.257 mg/L | 0.257 mg/L | none of 1 sample | 1 |
| Manganese limit 0.12 mg/L; 0.02 mg/L for taste and staining | 0.379 mg/L | 0.379 mg/L | 1 of 1 sample, at 1 well 1 over the taste and staining level | 1 |
| Uranium limit 0.02 mg/L | 0.000037 mg/L | 0.000037 mg/L | none of 1 sample | 1 |
| Nitrate (as nitrogen) limit 10 mg/L | 0.0055 mg/L | 0.0055 mg/L | none of 1 sample | 1 |
| Lead limit 0.005 mg/L | 0.00005 mg/L | 0.00005 mg/L | none of 1 sample | 1 |
These are samples of raw water, before any treatment, from wells in the Province's environmental monitoring records since 2000: its observation wells and groundwater surveys, water systems' wells and other drinking-water wells; wells at landfills, mines and permit holders' works are left out. A result below the lab's detection limit counts at that limit. Lead mostly comes from a well's pipes and fittings rather than the aquifer. Groundwater changes over short distances and with depth, so a nearby well says what the aquifer can hold, not what a well on this lot gives. Bacteria aren't shown: they depend on how each well is built and kept. Health Canada's Guidelines for Canadian Drinking Water Quality set the most a drinking water should hold: arsenic 0.010 mg/L, fluoride 1.5 mg/L, manganese 0.12 mg/L (and 0.02 mg/L for taste and for staining laundry and fixtures), uranium 0.02 mg/L, nitrate 10 mg/L as nitrogen (45 mg/L as nitrate) and lead 0.005 mg/L, with arsenic and lead kept as low as reasonably achievable. Our summary of Health Canada's summary table, read 2026-10-11.
Test your own well, for bacteria and these, at an accredited lab; your health authority can say which labs take samples from private wells. Health authority contacts.
Source: Environmental Monitoring Data System (EnMoDS) results, Province of BC (Open Government Licence – British Columbia); Health Canada's guidelines. Wells are those the Province links to this aquifer; a well with no link counts here when this is the only mapped aquifer under it. Wording by PlaceDossier.
Where it is
| Kind | Confined sand and gravel - glacial |
|---|---|
| Geological unit | Glaciofluvial deposits |
| Location, as described | Valemount |
| Area | 18 km² |
| Water use | Several uses (for example household wells, water systems, irrigation or industry) |
| Water quality concerns | None documented |
| Mapped | 2006 |
Confined: a layer of clay, silt or till lies over it, which slows water (and spills) from the surface; wells reach it through that layer. The province's page for this aquifer lists the studies behind it and its observation wells: GWELLS aquifer 800.
Sources: Ground Water Aquifers, Water Protection and Sustainability Branch, Province of BC and Groundwater Wells (GWELLS), Province of BC, as published on October 1, 2026 (Open Government Licence – British Columbia); ratings explained after Berardinucci and Ronneseth (2002), Guide to Using the BC Aquifer Classification Maps for the Protection and Management of Groundwater, BC Ministry of Water, Land and Air Protection. Summaries by PlaceDossier.
What this record doesn't cover
The province maps aquifers where wells and studies give enough to go on, mostly in settled valleys; most of BC isn't mapped, and a lot outside every outline can still have groundwater. Outlines are drawn from geology and well logs at the scale of the study, so an edge can be well off on the ground, and one aquifer can lie under another. Wells are linked to an aquifer by provincial staff from the driller's log: not every well inside an outline is linked, and well depths and yields are as the driller reported them, often from a short test.
These are mapped ratings and drillers' records, not a test of any one lot. Before you buy a property on a well, or plan to drill, ask a qualified hydrogeologist or a registered well driller what this aquifer gives where you are, and test the water.