PlaceDossier / BC places / Aquifers

Aquifer 375: Fort St. James bound by Necoslie River and Stuart

Aquifer 375 (Fort St. James bound by Necoslie River and Stuart) is a karstic limestone aquifer of 3.6 km² in the Bulkley-Nechako Regional District, mapped in 2007. The province rates its productivity low, its vulnerability to contamination from the surface low, and the demand on it low. 8 wells on record are linked to it; water-supply wells there are typically 97.2 m deep and tested at a median 4.2 L/min. It lies under Bulkley-Nechako, Electoral Area C.

BC aquifer 375 · bedrock · 3.6 km² · Bulkley-Nechako

How the province rates it

Productivity low, vulnerability low, demand low.

RatingWhat it means
Productivity
how much water the aquifer gives up to wells, judged from well yields, the aquifer material and pumping tests
lowWater comes slowly. The low band in the Province's aquifer classification guide is silt, fine sand or fractured bedrock, or typical well yields under about 0.3 L/s (18 L/min). A well may still supply a house, but it isn't assured.
Vulnerability
how easily something spilled at the ground surface could reach the water, judged from what lies above the aquifer and how deep the water is
low (class C)Better protected (class C), usually by clay or silt above it or deep water. Not immune: a gap in the cover or a badly sealed well can still let contaminants in.
Demand
how much the aquifer is used now, judged from the number and density of wells and what they're used for
lowLightly used: about 4 or fewer domestic wells per km² where homes rely on private wells.
Level of development Inferred
demand compared with productivity
Moderate (class II)Read by us from the guide's table of demand against productivity; where it gives two classes the mapper chose with local knowledge. Heavy (I): new wells should be carefully assessed; moderate (II): given careful thought; light (III): more use is usually fine if the aquifer can supply it.

Ratings are the province's, set when the aquifer was mapped (2007) from wells, geology and local studies. Vulnerability is about the ground, not what's built on it: a well-protected aquifer under a busy area can still be at more risk than an exposed one in the bush.

Sources: Ground Water Aquifers, Water Protection and Sustainability Branch, Province of BC and Groundwater Wells (GWELLS), Province of BC, as published on October 1, 2026 (Open Government Licence – British Columbia); ratings explained after Berardinucci and Ronneseth (2002), Guide to Using the BC Aquifer Classification Maps for the Protection and Management of Groundwater, BC Ministry of Water, Land and Air Protection. Summaries by PlaceDossier.

The wells in it

8 wells on record are linked to this aquifer.

Wells linked8 (6 water-supply)
Water-supply well depthmedian 97.2 m; middle half 80.8 m to 103 m (6 wells)
Tested yieldmedian 4.2 L/min; middle half 2.4 L/min to 14.8 L/min (6 wells tested)
Water level below groundmedian 15.2 m when drilled (3 wells)
Drilled1972 to 2005

Depths are how deep the driller finished the well; yields are the driller's test, often an hour or less, in litres per minute. A domestic well's yield is usually judged against the household's peak use; ask a driller what's enough for yours.

What the water tested for

No well sampled here had a median over Health Canada's limits.

1 well in this aquifer was sampled for the Province's records from 2008.

Typical well (median)Highest sampleSamples over the limitWells
Arsenic
limit 0.010 mg/L
0.00155 mg/L0.00155 mg/Lnone of 1 sample1
Manganese
limit 0.12 mg/L; 0.02 mg/L for taste and staining
0.00202 mg/L0.00202 mg/Lnone of 1 sample1
Uranium
limit 0.02 mg/L
0.000474 mg/L0.000474 mg/Lnone of 1 sample1
Lead
limit 0.005 mg/L
0.000135 mg/L0.000135 mg/Lnone of 1 sample1

These are samples of raw water, before any treatment, from wells in the Province's environmental monitoring records since 2000: its observation wells and groundwater surveys, water systems' wells and other drinking-water wells; wells at landfills, mines and permit holders' works are left out. A result below the lab's detection limit counts at that limit. Lead mostly comes from a well's pipes and fittings rather than the aquifer. Groundwater changes over short distances and with depth, so a nearby well says what the aquifer can hold, not what a well on this lot gives. Bacteria aren't shown: they depend on how each well is built and kept. Health Canada's Guidelines for Canadian Drinking Water Quality set the most a drinking water should hold: arsenic 0.010 mg/L, fluoride 1.5 mg/L, manganese 0.12 mg/L (and 0.02 mg/L for taste and for staining laundry and fixtures), uranium 0.02 mg/L, nitrate 10 mg/L as nitrogen (45 mg/L as nitrate) and lead 0.005 mg/L, with arsenic and lead kept as low as reasonably achievable. Our summary of Health Canada's summary table, read 2026-10-11.

Test your own well, for bacteria and these, at an accredited lab; your health authority can say which labs take samples from private wells. Health authority contacts.

Source: Environmental Monitoring Data System (EnMoDS) results, Province of BC (Open Government Licence – British Columbia); Health Canada's guidelines. Wells are those the Province links to this aquifer; a well with no link counts here when this is the only mapped aquifer under it. Wording by PlaceDossier.

Where it is

N 0500 m

The aquifer's outline as the Province maps it. Zoom in to see the lots over it; tap one for its report.
Share

TextEmail

Text and Email open your messages or email app with this message, ready to edit.

KindKarstic limestone
Location, as describedFort St. James bound by Necoslie River and Stuart
Area3.6 km²
Water useHousehold wells
Water quality concernsNone documented
Mapped2007

Bedrock: water moves through cracks in the rock, so two wells close together can find very different amounts. The province's page for this aquifer lists the studies behind it and its observation wells: GWELLS aquifer 375.

Sources: Ground Water Aquifers, Water Protection and Sustainability Branch, Province of BC and Groundwater Wells (GWELLS), Province of BC, as published on October 1, 2026 (Open Government Licence – British Columbia); ratings explained after Berardinucci and Ronneseth (2002), Guide to Using the BC Aquifer Classification Maps for the Protection and Management of Groundwater, BC Ministry of Water, Land and Air Protection. Summaries by PlaceDossier.

What this record doesn't cover

The province maps aquifers where wells and studies give enough to go on, mostly in settled valleys; most of BC isn't mapped, and a lot outside every outline can still have groundwater. Outlines are drawn from geology and well logs at the scale of the study, so an edge can be well off on the ground, and one aquifer can lie under another. Wells are linked to an aquifer by provincial staff from the driller's log: not every well inside an outline is linked, and well depths and yields are as the driller reported them, often from a short test.

These are mapped ratings and drillers' records, not a test of any one lot. Before you buy a property on a well, or plan to drill, ask a qualified hydrogeologist or a registered well driller what this aquifer gives where you are, and test the water.