PlaceDossier / BC places / Aquifers

Aquifer 1233: South of Aldergrove

Aquifer 1233 (South of Aldergrove) is a confined sand and gravel (glacial) aquifer of 17 km² in the Fraser Valley Regional District, mapped in 2025. The province rates its productivity low and its vulnerability to contamination from the surface low; its demand is not rated. 54 wells on record are linked to it; water-supply wells there are typically 57.2 m deep and tested at a median 189 L/min. It lies under Abbotsford (64%), Langley (district municipality) (36%).

BC aquifer 1233 · sand and gravel · 17 km² · Fraser Valley

How the province rates it

Productivity low, vulnerability low, demand not rated.

RatingWhat it means
Productivity
how much water the aquifer gives up to wells, judged from well yields, the aquifer material and pumping tests
lowWater comes slowly. The low band in the Province's aquifer classification guide is silt, fine sand or fractured bedrock, or typical well yields under about 0.3 L/s (18 L/min). A well may still supply a house, but it isn't assured.
Vulnerability
how easily something spilled at the ground surface could reach the water, judged from what lies above the aquifer and how deep the water is
low (class C)Better protected (class C), usually by clay or silt above it or deep water. Not immune: a gap in the cover or a badly sealed well can still let contaminants in.
Demand
how much the aquifer is used now, judged from the number and density of wells and what they're used for
not ratedThe province hasn't rated this for this aquifer.
Level of development Inferred
demand compared with productivity
unclearUnclear: the province hasn't rated both demand and productivity.

Ratings are the province's, set when the aquifer was mapped (2025) from wells, geology and local studies. Vulnerability is about the ground, not what's built on it: a well-protected aquifer under a busy area can still be at more risk than an exposed one in the bush.

Sources: Ground Water Aquifers, Water Protection and Sustainability Branch, Province of BC and Groundwater Wells (GWELLS), Province of BC, as published on October 1, 2026 (Open Government Licence – British Columbia); ratings explained after Berardinucci and Ronneseth (2002), Guide to Using the BC Aquifer Classification Maps for the Protection and Management of Groundwater, BC Ministry of Water, Land and Air Protection. Summaries by PlaceDossier.

The wells in it

54 wells on record are linked to this aquifer.

Wells linked54 (36 water-supply)
Water-supply well depthmedian 57.2 m; middle half 47.8 m to 63.8 m (36 wells)
Tested yieldmedian 189 L/min; middle half 94.6 L/min to 303 L/min (29 wells tested)
Water level below groundmedian 21.6 m when drilled (29 wells)
Flowing (artesian) wells1: water rose to or above the ground when drilled
Drilled1958 to 2022
Well depth deeper than 66% of the 637 BC aquifers with at least 10 wells with a depth
131030100300 m Median 57.2 m from 36 wells
Tested yield higher than 92% of the 542 BC aquifers with at least 10 wells tested
1310301003001,0003,000 L/min Median 189 L/min from 29 wells

This aquifer's medianIts middle half of wellsAnother BC aquifer's median

Depths are how deep the driller finished the well; yields are the driller's test, often an hour or less, in litres per minute. A domestic well's yield is usually judged against the household's peak use; ask a driller what's enough for yours.

What the water tested for

The median arsenic was over Health Canada's limit at 1 of 1 wells sampled here.

1 well in this aquifer was sampled for the Province's records from 2004 to 2010.

Typical well (median)Highest sampleSamples over the limitWells
Arsenic
limit 0.010 mg/L
0.0134 mg/L0.0143 mg/L10 of 11 samples, at 1 well1
Fluoride
limit 1.5 mg/L
0.11 mg/L0.13 mg/Lnone of 10 samples1
Manganese
limit 0.12 mg/L; 0.02 mg/L for taste and staining
0.043 mg/L0.0557 mg/Lnone of 11 samples
9 over the taste and staining level
1
Uranium
limit 0.02 mg/L
0.000052 mg/L0.000082 mg/Lnone of 11 samples1
Nitrate (as nitrogen)
limit 10 mg/L
0.006 mg/L0.09 mg/Lnone of 9 samples1
Lead
limit 0.005 mg/L
0.00014 mg/L0.0006 mg/Lnone of 11 samples1

These are samples of raw water, before any treatment, from wells in the Province's environmental monitoring records since 2000: its observation wells and groundwater surveys, water systems' wells and other drinking-water wells; wells at landfills, mines and permit holders' works are left out. A result below the lab's detection limit counts at that limit. Lead mostly comes from a well's pipes and fittings rather than the aquifer. Groundwater changes over short distances and with depth, so a nearby well says what the aquifer can hold, not what a well on this lot gives. Bacteria aren't shown: they depend on how each well is built and kept. Health Canada's Guidelines for Canadian Drinking Water Quality set the most a drinking water should hold: arsenic 0.010 mg/L, fluoride 1.5 mg/L, manganese 0.12 mg/L (and 0.02 mg/L for taste and for staining laundry and fixtures), uranium 0.02 mg/L, nitrate 10 mg/L as nitrogen (45 mg/L as nitrate) and lead 0.005 mg/L, with arsenic and lead kept as low as reasonably achievable. Our summary of Health Canada's summary table, read 2026-10-11.

Test your own well, for bacteria and these, at an accredited lab; your health authority can say which labs take samples from private wells. Health authority contacts.

Source: Environmental Monitoring Data System (EnMoDS) results, Province of BC (Open Government Licence – British Columbia); Health Canada's guidelines. Wells are those the Province links to this aquifer; a well with no link counts here when this is the only mapped aquifer under it. Wording by PlaceDossier.

Where it is

N 01 km

The aquifer's outline as the Province maps it. Zoom in to see the lots over it; tap one for its report.
Share

TextEmail

Text and Email open your messages or email app with this message, ready to edit.

KindConfined sand and gravel - glacial
Geological unitFort Langley Formation
Location, as describedTownship of Langley / Abbotsford
Area17 km²
Mapped2025

Confined: a layer of clay, silt or till lies over it, which slows water (and spills) from the surface; wells reach it through that layer. The province's page for this aquifer lists the studies behind it and its observation wells: GWELLS aquifer 1233.

Sources: Ground Water Aquifers, Water Protection and Sustainability Branch, Province of BC and Groundwater Wells (GWELLS), Province of BC, as published on October 1, 2026 (Open Government Licence – British Columbia); ratings explained after Berardinucci and Ronneseth (2002), Guide to Using the BC Aquifer Classification Maps for the Protection and Management of Groundwater, BC Ministry of Water, Land and Air Protection. Summaries by PlaceDossier.

What this record doesn't cover

The province maps aquifers where wells and studies give enough to go on, mostly in settled valleys; most of BC isn't mapped, and a lot outside every outline can still have groundwater. Outlines are drawn from geology and well logs at the scale of the study, so an edge can be well off on the ground, and one aquifer can lie under another. Wells are linked to an aquifer by provincial staff from the driller's log: not every well inside an outline is linked, and well depths and yields are as the driller reported them, often from a short test.

These are mapped ratings and drillers' records, not a test of any one lot. Before you buy a property on a well, or plan to drill, ask a qualified hydrogeologist or a registered well driller what this aquifer gives where you are, and test the water.