PlaceDossier / BC places / Aquifers

Aquifer 1216: Vedder Mountain Northwest Bedrock

Aquifer 1216 (Vedder Mountain Northwest Bedrock) is a fractured crystalline bedrock aquifer of 26 km² in the Fraser Valley Regional District, mapped in 2019. The province rates its vulnerability to contamination from the surface moderate; its productivity and demand are not rated. 7 wells on record are linked to it; water-supply wells there are typically 32.8 m deep and tested at a median 24.6 L/min. It lies under Chilliwack (46%), Abbotsford (28%), Fraser Valley, Electoral Area H (24%).

BC aquifer 1216 · bedrock · 26 km² · Fraser Valley

How the province rates it

Productivity not rated, vulnerability moderate, demand not rated.

RatingWhat it means
Productivity
how much water the aquifer gives up to wells, judged from well yields, the aquifer material and pumping tests
not ratedThe province hasn't rated this for this aquifer.
Vulnerability
how easily something spilled at the ground surface could reach the water, judged from what lies above the aquifer and how deep the water is
moderate (class B)Some natural protection (class B), which can vary across the aquifer.
Demand
how much the aquifer is used now, judged from the number and density of wells and what they're used for
not ratedThe province hasn't rated this for this aquifer.
Level of development Inferred
demand compared with productivity
unclearUnclear: the province hasn't rated both demand and productivity.

Ratings are the province's, set when the aquifer was mapped (2019) from wells, geology and local studies. Vulnerability is about the ground, not what's built on it: a well-protected aquifer under a busy area can still be at more risk than an exposed one in the bush.

Sources: Ground Water Aquifers, Water Protection and Sustainability Branch, Province of BC and Groundwater Wells (GWELLS), Province of BC, as published on October 1, 2026 (Open Government Licence – British Columbia); ratings explained after Berardinucci and Ronneseth (2002), Guide to Using the BC Aquifer Classification Maps for the Protection and Management of Groundwater, BC Ministry of Water, Land and Air Protection. Summaries by PlaceDossier.

The wells in it

7 wells on record are linked to this aquifer.

Wells linked7 (4 water-supply)
Water-supply well depthmedian 32.8 m; middle half 24.9 m to 59.8 m (4 wells)
Tested yieldmedian 24.6 L/min; middle half 18 L/min to 31.2 L/min (2 wells tested)
Water level below groundmedian 6.2 m when drilled (2 wells)
Drilled1973 to 1998

Depths are how deep the driller finished the well; yields are the driller's test, often an hour or less, in litres per minute. A domestic well's yield is usually judged against the household's peak use; ask a driller what's enough for yours.

Is the water level falling?

1 provincial observation well still measured here.

Observation well 255water level stable or no clear trend over 2014 to 2023, as over the whole record since 1983; water typically 3 m below ground in a well 37 m deep

Observation wells are the Province's monitoring wells, their water level measured for years or decades. The trend is the Province's reading of one well's yearly levels: a decline of 3 to 10 cm a year that the record clearly shows is a moderate rate, 10 cm or more a large one, anything not clear is stable or no clear trend. It shows how the aquifer has behaved there, not what a well on this lot will give; confirm with a qualified hydrogeologist or registered well driller.

Source: Long-term Trends in Groundwater Levels in B.C., Environmental Reporting BC (Provincial Groundwater Observation Well Network), records to December 2023 (Open Government Licence – British Columbia). Wording by PlaceDossier.

What the water tested for

No well sampled here had a median over Health Canada's limits.

1 well in this aquifer was sampled for the Province's records from 2004 to 2014, one of them the Province's observation well 255.

Typical well (median)Highest sampleSamples over the limitWells
Arsenic
limit 0.010 mg/L
0.000085 mg/L0.0001 mg/Lnone of 16 samples1
Fluoride
limit 1.5 mg/L
0.12 mg/L0.14 mg/Lnone of 15 samples1
Manganese
limit 0.12 mg/L; 0.02 mg/L for taste and staining
0.00392 mg/L0.0136 mg/Lnone of 16 samples1
Uranium
limit 0.02 mg/L
0.0000025 mg/L0.000013 mg/Lnone of 16 samples1
Nitrate (as nitrogen)
limit 10 mg/L
0.002 mg/L0.019 mg/Lnone of 12 samples1
Lead
limit 0.005 mg/L
0.000025 mg/L0.000168 mg/Lnone of 16 samples1

These are samples of raw water, before any treatment, from wells in the Province's environmental monitoring records since 2000: its observation wells and groundwater surveys, water systems' wells and other drinking-water wells; wells at landfills, mines and permit holders' works are left out. A result below the lab's detection limit counts at that limit. Lead mostly comes from a well's pipes and fittings rather than the aquifer. Groundwater changes over short distances and with depth, so a nearby well says what the aquifer can hold, not what a well on this lot gives. Bacteria aren't shown: they depend on how each well is built and kept. Health Canada's Guidelines for Canadian Drinking Water Quality set the most a drinking water should hold: arsenic 0.010 mg/L, fluoride 1.5 mg/L, manganese 0.12 mg/L (and 0.02 mg/L for taste and for staining laundry and fixtures), uranium 0.02 mg/L, nitrate 10 mg/L as nitrogen (45 mg/L as nitrate) and lead 0.005 mg/L, with arsenic and lead kept as low as reasonably achievable. Our summary of Health Canada's summary table, read 2026-10-11.

Test your own well, for bacteria and these, at an accredited lab; your health authority can say which labs take samples from private wells. Health authority contacts.

Source: Environmental Monitoring Data System (EnMoDS) results, Province of BC (Open Government Licence – British Columbia); Health Canada's guidelines. Wells are those the Province links to this aquifer; a well with no link counts here when this is the only mapped aquifer under it. Wording by PlaceDossier.

Where it is

N 02 km

The aquifer's outline as the Province maps it. Zoom in to see the lots over it; tap one for its report.
Share

TextEmail

Text and Email open your messages or email app with this message, ready to edit.

KindFractured crystalline bedrock
Geological unitPermian to Triassic Vedder Complex, locally Jurassic to Cretaceous
Location, as describedSouthwest Chilliwack
Area26 km²
Mapped2019

Bedrock: water moves through cracks in the rock, so two wells close together can find very different amounts. The province's page for this aquifer lists the studies behind it and its observation wells: GWELLS aquifer 1216.

Sources: Ground Water Aquifers, Water Protection and Sustainability Branch, Province of BC and Groundwater Wells (GWELLS), Province of BC, as published on October 1, 2026 (Open Government Licence – British Columbia); ratings explained after Berardinucci and Ronneseth (2002), Guide to Using the BC Aquifer Classification Maps for the Protection and Management of Groundwater, BC Ministry of Water, Land and Air Protection. Summaries by PlaceDossier.

What this record doesn't cover

The province maps aquifers where wells and studies give enough to go on, mostly in settled valleys; most of BC isn't mapped, and a lot outside every outline can still have groundwater. Outlines are drawn from geology and well logs at the scale of the study, so an edge can be well off on the ground, and one aquifer can lie under another. Wells are linked to an aquifer by provincial staff from the driller's log: not every well inside an outline is linked, and well depths and yields are as the driller reported them, often from a short test.

These are mapped ratings and drillers' records, not a test of any one lot. Before you buy a property on a well, or plan to drill, ask a qualified hydrogeologist or a registered well driller what this aquifer gives where you are, and test the water.